Specialised Testing Tool

KA-2899K3 (Return Fuel Volume Tester for Common Rail Injectors)        This specialised tool has been developed to assist with accurate diagnosis of common rail injector faults on diesel engines. It is used to measure the return flow rate / volume of each injector individually. This information is necessary when diagnosing a faulty injector. The benefit of using the following Tool is the ability to accurately measure and compare injector return flow rates while the vehicle is running or will not start. This also gives you the ability to conclusively identify a faulty injector. Features: Sturdy quality plastic case and components Precise increments shown on the tubes and bottles for accurate measurement every time Two sets of measuring devices that provide greater diagnosis opportunities with three tests available Easily compare injector return flow rates from all injectors Assortment of fittings to suit both Bosch and Denso injectors Comprehensive user instructions and technical check sheet

KA-1020 (6 WAY MULTI-PURPOSE HYDRAULIC PULLER)

This specialised tool is 6 Way Multi Purpose Hydraulic Gear Puller Kit.

Content:
1020-1 10 Ton Hydraulic ram----------------------1pc
1020-2 Combination cross head--------------------1pc
1020-3 Combination leg----------------------------3pcs
1020-4 Steel plate------------------------------------6pcs
1020-5 Extension rod 1 x 1-1/4"--------------------1pc
1020-6 Extension rod 1 x 2"------------------------1pc
1020-7 Screw nut & washer------------------------6pcs

KA-1242 (ADJUSTABLE TORQUE SCREWDRIVER)

• Two windows display for in-lb and N.m.
• Accuracy: ± 6%
• Soft grip handle manufactured from TPR for comfortable use
• Quick change design with mini effort
• Application: air bag, crash sensor, inertia reel fixtures
• PAT. & SGS

1) For clamping plumbing and round-off screws
2) Smooth fast screw clamping and releasing

• Much stronger to clamp the screws especially on round ones
• For clamping plumbing and round-off screws
• For clamping small to large screws
• Smooth fast screw clamping and releasing
• Material: Jaw-CR-MO; Body-CR-MO

KA-1271 (PARROT PLIER WITH SAWTEETH)

1) For clamping plumbing and round-off screws;
2) Smooth fast screw clamping and releasing.

• Much stronger to clamp the screws especially on round ones
• For clamping plumbing and round-off screws;
• For clamping small to large screws
• Smooth fast screw clamping and releasing

Material: Jaw-CR-MO; Body-CR-MO

KA-2054 (3PC DIESEL INJECTOR PULLER SET)

This specialised tool can remove stubborn diesel injector and no need to remove cover and the use of slide hammer.

• This special designed diesel injector puller set is ideally for the need to remove stubborn diesel injector. No need to remove cam cover and the use of slide hammer.
• Fitted mainly to Mercedes C-class, E-class, Sprinter Vehicles and Chrysler Grand Cherokee 27crd(00-)

6PCS 1/2'' & 3/4'' Dr. Twist Socket Set
For removal of damaged bolts / nuts

Internal / External
"T" Bar and screw action gives precise control.
Supplies with 4 pairs of tips.

Applications:   44 - 178mm (diameter) 1-3/4''-7''

KA-2714K1 (Air Power Brake Calliper Wind Back Tool Kit)

Air Power Brake Calliper Wind Back Tool Kit
(With 17pc Brake Pads)

KA-2720 (Finger Saver Wire Piercing Guide)

An ingenious device that eliminates stabbed fingers.

Quickly, easily and safely guides the pick point of any circuit tester into the centre of all primary automotive electrical wire. It also can hold the circuit tester in position that allow you working with both hands free.

Resists gasoline, oil, thinners, and other shop chemicals.

KA-2877N (Diesel Injector Puller)

This specialised tool assists removal of stubborn Bosch and Lucas diesel injectors time and money saving, especially when injectors are difficult to remove.

• With M8 / M12 / M14 ADAPTORS
• Length:230mm

KA-2886 (MULTI-FUNCTION INSPECTION TOOL)

1PC- Aluminium Interchangeable Handle
1PC- Inspection Mirror
1PC- 6 lbs Magnetic retriever
1PC- 10 flexible adapter
1PC- 90° & 35° bent adapter
1PC- 8 straight adapter
1PC- UV light
1PC- LED light

KA-2899KQC (36PCS FOR FLOW METER COMMON RAIL [QUICK REPLACEMENT])

This specialised tooling is designed for rapidly and effectively measuring the amount of fuel that every injector returns to the deposit tank, so that you will know if any injector is damaged.

• Directly measure return flow of the injector
• Measure return flow using external flow meter
• Possibility of simultaneous measurement of up to 6 injectors
• Box for transportation and storage included
• Set included 24pc injector adaptors: apply for BOSH-01, SIEMENS-02, DENSO-03 and DELPHI injector

KA-2911A (Timing Pulley Puller)

Feature:

• Draw pulleys by the holes without causing damage.
• Moving legs adapt to differ pulley diameters.
• Compact design for using with engine in situ.

KA-2917 (6PCS 3/8" DR. Jointed Glow Plug Socket Set)       

This Specialised Tool has been specially designed for removal and replacement of glow plugs easily.

Material: CR-V Satin Finish
Made with built-in retaining O-ring.

KA-2936KM (4PC/Set Flexible Flare Nut Wrench Set 6X12PT)

SIZE: 8, 10, 11, 12MM
MIRROR FINISH

KA-2936KS (4 PC Single Flexible Flare Nut Wrench Set [8,10,11,12 MM])

SIZE: 8,10,11,12MM
SATIN FINISH

KA-2985 (3/8'' DR. TAP HOLDER SOCKET M4 ~ M8)

3/8" (9.5mm) Tap Holder Socket
Attach to any 3/8" Ratchet Wrench or T-bar to use.

KA-2986 (3/8'' DR. TAP HOLDER SOCKET M10 ~ M12)

3/8" (9.5mm) Tap Holder Socket
Attach to any 3/8" Ratchet Wrench or T-bar to use.

KA-2987 (3/8'' DR. TAP HOLDER SOCKET M13 ~ M14)

3/8" (9.5mm) Tap Holder Socket.
Attach to any 3/8" Ratchet Wrench or T-bar to use.

KA-2994B (System Release)

1) Release the Flat Plug Contact set with Ease and Cause NO Damage.
2) Easily and Fast Repair the Connection Defects or Corrosion.

KA-3523 (GLOW-PLUG CONNECTOR PLIERS [STRAIGHT])

This specialised tool has been developed to remove stubborn - awkward to reach Glow-Plug connectors, commonly on the latest generation of engines.

e.g. Mercedes, BMW, VW-Audi etc.

KA-3563 (MULTI-PURPOSE CONNECTOR [HS CODE: 820559])

Various male / female connectors are designed and made for various vehicle applications. It is perfect for quickly and accurately checking of electrical circuits.

Application of Operation:

• When checking the parts, it could connect the back of terminal directly, and it would not to damage the circuit. Reduce the circuit rust and avoid adding impedance.
• Apply to any Automotive Multimeter, the extended line of probe for oscilloscope. More convenient connection and rapid checking.
• When checking the electric current, only use the lines to connect the circuit, do not need to cut the electric wires.
• Variable Resister can simulate the pretend signal of coolant temperature sensor, throttle valve sensor and send the pretend signal to computer. It would avoid the risk to change the new parts again.
• Equip 2 sets LED light. It can supervise hall effect, photoelectric signal, nozzle, electromagnetic valve, electromagnetic valve of transmission shift gear etc, and control signals.
• SRS Connector can simulate airbag and routed contracting device of safety belt to avoid accident or miss-judgment.
• Various wires in this box, it is suitable for the Europe, America and Japan terminal. Highly common usage and convenience.

KA-3635K (1/2'' DR. OPEN ENDED RING WRENCH SOCKET SET L: 100MM)

This specialised tool has been specially designed to loosen and tighten nuts / bolts in confined spaces.

e.g. Fuel Injector Connections

KA-3636B (DIESEL INJECTOR SEAT CUTTER [HS CODE: 820559])

This specialised tool has been developed to identify injector "blow-by" exists.

• Identify injector "blow-by" exists (The leaking of combustion gas from cylinder through the injector seat, the blow-by causes starting symptoms and poor running, excessive smoke, tar build-up, loss and noise of compression).
• Gain access to the injectors and remove them.
• Select required reamer onto pilot post and tighten internal hex screw.
• Place assembled cutter into injector recess.
• Using the T bar and socket supplied: apply only a small amount of pressure whilst turning the cutter in a clockwise direction only. Use a small amount of light lubricant whilst performing the cut to reduce chattering and help to give a flat cut. Do not over cut the seat,  only remove enough metal to form a good seat.
• Thoroughly clean the seat and remove all swarf.
• Fit injectors as per manufacturers' instructions.

Kit Contents:

• 15mm Flat Reamer for Universal injector.
• 17mm Flat Reamer for Delphi/Bosch injectors (BMW/PSA/Renault/Ford).
• 19mm Flat Reamer for Bosch injectors (Mercedes CRD).
• 19mm Angled Reamer for Fiat/Iveco.
• T handle x 1pc
• I Pilot post x 1pc

KA-3636D (8PCS DIESEL INJECTOR SEAT CUTTER SET)

This specialised tool is designed for cleaning under injection washer after replacing injector.

It is necessary to clean under and above a washer for a perfect fit of a new or replaced diesel injector.

Do not use with air tools.

KA-3656 (DIESEL INJECTION PUMP PULLER FOR LAND ROVER)

This specialised tool has been developed for holding the sprocket / chain in the place when disassembling the VP44 injection pump and high pressure pump.

• Common rail fitted to Land Rover engines: Land Rover / Freelander (TD4) / Rover / 75 (M47)

KA-3659 (CDI-Glow Plug Tool)

This specialised tool is designed for removing glow plugs from cylinder head, especially for glow plugs that are stuck because of carbonization remains.

Cylinder head does not need to be removed anymore. Fits all Mercedes 10mm glow plugs, engine codes 611-612-613 etc.

KA-3969 (INJECTOR NOZZLE PULLER WITH SLIDE HAMMER)

• For removing adapted tight common rail injectors without having to disassemble cylinder head.
• Use for Mercedes-Benz CDI engines 611.612.613 etc.
• Injection puller with impact hammer, injection nozzles that do not fit very tightly can be pulled out without needing to take them apart or remove the cylinder block.

KA-3998A-260 (INTERNAL SPARK PLUG RETHREAD TOOL (THREAD CHASER) 12MMX260L)

This specialised tool uses the better threads at the base of the spark plug port and greatly reduces the chance of debris from falling into the cylinder.
It is unique design allows for chasing spark plug threads from inside the cylinder head and working outward.

Use the good threads at the base of the port.
Reduced dirt and metal from being driven into the cylinder head.
Use light grease on the end to trap filings and keep tool easy to use.

Length of 260mm (10'') allows for deep well plugs.

KA-3998B-260 (INTERNAL SPARK PLUG RETHREAD TOOL (THREAD CHASER) 14MMX260L)

The tool uses the better threads at the base of the spark plug port and greatly reduces the chance of debris from falling into the cylinder.

It 's unique design allows for chasing spark plug threads from inside the cylinder head and working outward.

Use the good threads at the base of the port.
Reduced dirt and metal from being driven into the cylinder head.
Use light grease on the end to trap filings and keep tool easy to use.

Length of 260mm (10'') allows for deep well plugs.

KA-4032 (INJECTOR NOZZLE TOOL SET)

• Mercedes CDI engines (German Utility Model)
• Suitable for Mercedes CDI engines OM 611, 612, 613, etc.
• This injector nozzle Tool set (comprising nozzle puller, nozzle puller, milling cutter, compressed air adapter, thread tap and plastic case) makes it possible to remove the injector nozzles correctly.

KA-4033 (GLOW PLUG TOOL SET)

This specialised tool has been developed for Mercedes CDI engines. Suitable for Mercedes CDI engines OM 611, 612 and 613.

The glow plug tool set KA-4033 enables the correct removal of burnt and/or stuck due to corrosion or torn off glow plugs as well as the repair of the glow plug retaining thread.

The cylinder head does not have to be removed.

(Note: Screwing the compressed air adapter into the injector nozzle bore and injecting compressed air into the combustion chamber prevents dirt and mental particles from entering into the combustion chamber)

Advantages:

• Large time saving and cost saving
• Clean working methods
• The tool is easy to operate

KA-4034 (Injector Nozzle Puller for Mercedes CDI)

This specialised tool is Injector Nozzle Puller for Mercedes CDI.

• Suitable for Mercedes CDI engine OM 668, e.g. A-Class.
• The injector nozzle puller makes it possible to remove even nozzles that are a very tight fit in the cylinder head, without the cylinder head having to be removed from the engine.

KA-4190 (12PCS MINI PICK AND HOOK SET WITH MAGNET)

This specialised tool has been developed to use in many ways around the vehicle from seals to cotter pin removal, cleaning nooks and crannies, bushing, O-ring removal, alignment, scribing, piercing holes in leather or fabric, etc.

The long grip handles provide comfort and control while using, the top magnets increase its multi-purpose.

Set contains 12 different type picks and hooks and packaged in storage pouch.

Material: stainless 304

KA-4293A (20MM TUNGSTEN CARBIDE SCRAPER)

This specialised tool has been developed to turn blade over for 3 additional surfaces for a total of 6 possible cutting edges.

KA-4294K2 (COMBINATION 6 CHANNEL ELECTRONIC STETHOSCOPE KIT)

This specialised tool has been developed to use for: road test diagnosis, under chassis, under hood and fuel injectors.

• Use to locate & identify engine noise
• Super sensitive microphone pick-up
• Flexible non-conductive shaft
• Cushioned headphones

Component stethoscope

• Detect & isolate noise components
• Enables road test diagnosis
• 6 channel sensor selector unit
• 6 pick up sensors 4.8m long cord

Use for: road test diagnosis / under chassis / under hood / fuel injectors.

The chassis EAR is a versatile electronic listening tool, which is designed to allow the user to listen to amplified sounds through a professional set of headphones during a road test.

There are 6 extremely sensitive microphone/clamps that can be attached adjacent to many difficult to diagnose vehicle parts and 1 extension lead.

KA-4296 (GLOW PLUG REMOVAL SET)

Diesel Engine requires GLOW PLUG for combustion process in engine cylinder. The heating element in glow plug heat up and drive the cylinders gradually.

However, the heating elements are very delicate, and require special tool for removing the glow plug.
It is the best tool set for successful removal of glow plug.

Specification

Part No.
1	Hex 12mm spindle, Hex 30mm nut, cone center tool
2	Drill installer
7	1/4” -28 UNF, Hex 9mm –2pcs
8	Ø6 x 3.5 x 40L –2pcs
9	Alley Key
10	9.7mm square socket
11	7 x 5.5
12	9 x 5.5
13	T-handle
14	Ø3.5 drill –2pcs
15	M10 x P10
16	M8 x 1.0
17	1/4” – 28UNF

KA-4422K (Vacuum/Pressure Pump)

Mechanical Engine Condition 

• VACUUM GAUGE
• CYLINDER LEAKAGE
• VALVE STEM OIL SEALS
• HEAVY DUTY DIESEL PISTON PIN
• RETAINER LEAKAGE
• TURBOCHARGER WASTEGATES
• MOTORCYCLE AND MARINE
• SEALING & DEFECTIVE GASKETS TESTINGS
• VACUUM PUMP PROVIDES

Many Tests Including But Not Limited to the Following:

• AUTOMATIC TRANSMISSION
• VACUUM MODULATORS
• BODY AND ACCESSORIES
• VACUUM RESERVOIRS
• AIR CONDITIONING AND HEATING
• HEATER CORES
• BRAKE SYSTEMS
• ANTILOCK BRAKE SYSTEM
• CONVENTIONAL BRAKE SYSTEM
• POWER BRAKE SYSTEM
• COMPUTERIZED ENGINE CONTROL SYSTEMS
• FORD EED-III AND MCU SYSTEM
• CHRYSLER ELECTRONIC FUEL CONTROL SYSTEM
• AMERICAN MOTORS ENGINE CONTROLS
• EMISSION CONTROL SYSTEM
• HEATED-INLET AIR SYSTEM
• EGR (Exhaust gas recirculation) system
• Engine tune-up
• Carburettor adjustments and service
• Carburettor chokes
• Propane carburettor service
• FUEL SYSTEM PROBLEMS
• FUEL TANK
• FUEL LINES
• FUEL PUMPS
• FUEL PRESSURE REGULATOR
• LGNITION SYSTEM SERVICES
• SYSTEM FUNCTIONS
• LGNITION TIMING
• POWER BRAKE SYSTEM

KA-5134 (12PC ENGINE TIMING SET FOR LAND ROVER)

• New EDC Manual Transmission Timing Pin
• 200 TDI 300 TDI & 2.5 Diesel Engines
• Combined Crankshaft Damper Puller and Fuel Pump Gear Locking Tool

KA-5167A (9PCS Common Rail Injectors Extractor Set)

Feature:

• With slide hammer for DB CDI-engines & Mercedes CDI engines OM 611, 612, 613 etc.
• For removing stuck and the seized common-rail injectors without dismount the cylinder head.
• The sturdy construction will enable the swift removal of even the most severely seized in injector.

Specification:

• Material: S45C steel
• Total Length: 350mmL
• Contents: Slide Hammer (1.75kgs)

Adaptor M17 x 1.0
Adaptor M27 x 1.0 for Bosch injector nozzle

Adaptor: Puller w/M12 x 1.75

KA-5167B (6PCS INJECTOR PULLER FOR MERCEDES BENZ [SLIDE HAMMER STYLE])

• For removing adapted tight common rail injectors without having to disassemble cylinder head.
• Use for Mercedes-Benz CDI engines 611.612.613 etc.
• Injection puller with impact hammer, injection nozzles that do not fit very tightly can be pulled out without needing to take them apart or remove the cylinder block.

KA-5167C (7PCS INJECTOR PULLER FOR MERCEDES BENZ [SLIDE HAMMER STYLE])

This six piece puller set has been especially designed for removing stubborn injectors on Mercedes Benz vehicles fitted with CDI engines.

Packed in a blow moulded case.

KA-5547(4PC/SET MINI SNAP-RING PLIER SET FOR S-RING & R-RING TOOLS)

For S-Ring & R-Ring Tools

KA-6262 (1/2'' VACUUM SOCKET)

• 1/2 inch DR x 29mm x 90mmL
• 6PT
• 7mm slot

KA-6268A (1/2'' INJECTOR SOCKET [27MM])

• 1/2inch DR x 27 x 78mmL
• 12PT

KA-6268B (1/2'' INJECTOR SOCKET [27MM])

• 1/2inch DR x 27 x 78mmL
• 6PT

KA-6269 (1/2'' INJECTOR SOCKET [22MM])

• 1/2inch DR x 22 x 110mmL

           Black Finished

KA-6270A (1/2'' INJECTOR SOCKET [28MM])

• 1/2inch DR x 28 x 78mmL
• 12PT
  

KA-6282A (6PC DIESEL INJECTOR SOCKET SET)

1/2inch DR , CR-V
27mm x 12PT x 78mmL
22mm x 12PT x 78mmL
22mm x 6PT x 110mmL
28mm x 12PT x 78mmL
21mm x 12PT x 78mmL
28mm x 6 PT x 90mmL

KA-6537K (4-IN-1 E-RING TOOL SET INSERT & RELEASE)

4-in-1 E-Ring Tool Set Insert & Release.

KA-6678B (PIPE DISCONNECTION SET)

5/16", 3/8", 1/2", 5/8", 3/4", 7/8"

KA-6713K (43pcs UNF, UNC & Metric Rethreader Kit)

Content:
21pcs rethreader dies:
1/4", 5/16", 3/8", 7/16", 1/2." 9/16", 5/8" UNF
1/4", 5/16", 3/8", 7/16", 1/2". 9/16", 5/8" UNC
6x1.00, 8x1.25, 10x1.25, 10x1.50, 12x1.25, 12x1.5, 12x1.75mm

19pcs rethreader tap sizes:
1/4", 5/16", 3/8", 7/16", 1/2", 9/16" UNF
1/4", 5/16", 3/8", 7/16", 1/2", 9/16" UNC
6x1.00, 8x1.25, 10x1.25, 10x1.50, 12x1.25, 12x1.5, 12x1.75mm

Description pitch sizes:
METRIC FILE: 0.75, 1.00, 1.25, 1.75, 2.00, 2.50 and 3.00mm
SAE FILE: 11, 12, 13, 14, 16, 18, 20 and 24
SAE FILE: 9, 10, 12, 16, 20, 27, 28 and 32

KA-6971K (CRANKSHAFT & CAMSHAFT SEAL REMOVER AND INSTALLER KIT)

Quick and easy work for both removal and installation work

• Ideal for both crankshaft and camshaft seal
• Quick and easy work for both removal and installation work
• Master kit includes wide size seal installers
• Provided with 2 seal removers with different length and angle fits wide applications
• Angled blade seal remover is ideal for removing seals in limited space

KA-6972K (MASTER SEAL REMOVER & SOFT HOSE PICK SET)

Quick and easy work for both removal and installation work

• Easily remove seals or o-ring or pick soft hoses on vehicle
• Provided with different length and angle fits wide applications
• Angled blade is ideal for removing seals in limited space
• Blade material: SCM 440applications

KA-6973K (12PCS QUICK FLUID STOPPER SET)

This specialised tool has been developed to quickly stop fluid from the separated fuel hoses.

Available for injection hose or fuel supply hose adaptors.

• Quickly stop fluid from the separated fuel hoses.
• Available for injection hose or fuel supply hose adaptors.

KA-7191C (Diesel Engine Cylinder Leakage Tester Kit)

This specialised tool covers most popular cars and vans.

It has additional glow plug adaptors for more coverage and it also includes the adaptor set for clamp-type injectors to cover more car, van, truck, bus, agricultural and marine applications.

Glow plug adaptor application: Alfa, BMW, Chrysler, Daewoo, Ford, Hyundai, Isuzu, Land Rover, LDV, Mazda, Mercedes Benz, Mitsubishi, Nissan, Opel, PSA, Renault, Saab, Suzuki, Toyota, VAG, Vauxhall, Volvo Diesel Engine.

Injectors: M20, M22, M24 & Ford Stanadyne injector plus clamp-on injector.

KA-7191D (Diesel Engine Compression Tool Kit)

This specialised tool includes the additional Clamp-on Injector Adaptor Set, the large 2-1/2, 70 bar (1000psi) gauge with rubber bumper, straight and right angled connect fittings, wide range of glow plug and injector adaptors which enables the kit to cover the majority of car, van, truck, bus, agricultural and marine diesel engines.

Glow plug adaptor application: Alfa, BMW, Chrysler, Daewoo, Ford, Hyundai, Isuzu, land Rover, LDV, Mazda, Mercedes Benz, Mitsubishi, Nissan, Opel, PSA, Renault, Saab, Suzuki, Toyota, BAG, Vauxhall, Volvo Diesel Engine.

Injector: M20, M22, M24 & Ford Stanadyne injector plus clamp-on injector.

KA-7228 (Hose Clamp)

This specialised tool has been developed to stop the oil flow and avoid damaging hoses.

• Stop the oil flow and avoid damaging hoses.
• Adjustable for most kinds of flexible hoses, particularly for brake, fuel or cooling system hoses.
• Length 310mm, extension hose clamp helps repair work.
• Maximum application: 25.4mm.
• Adjust the movable ball (1) and fit the width of hose, then screw the adjustable head (2).

KA-7230K (UNIVERSAL RADIATOR PRESSURE TESTER KIT FOR COOLING SYSTEM TESTERS)

Availability range for the testing head:

NO 0: Needle type thermometer
NO 1: Manual pumping set.
NO 2: TRUCK, GM (CADILLAC)
NO 3: BENZ, FORD, TRUCK, JAPANESE 123 SERIES, GM (BUICK), JEEP
NO 4: PEUGEOT, JAPANESE 124 SERIES (MITSUBISHI, NISSAN, MAZDA, TOYOTA, SUBARU, INFINITI, GEO, SUZUKI, ISUZU, LEXUS)
NO 5: JAPANESE 125 SERIES (HONDA, TOYOTA, SUZUKI, MITSUBISHI)
NO 6: OPEL, VW, FORD, BMW245, SAAB, JAGUAR
NO 7: VOLVO, SAAB, AUDI, CITRON, RENAULT, FIAT, PEUGIOT, ALFA, JEEP
NO 8: NEW VW
NO 9: VW T4, NEW AUDI A4, A5, A6, BMW 345
NO 10: BMW
NO 11: AUDI, VW
NO 12: FORD, INTERNATIONAL, GM, ROVER
NO 13: BENZ

KA-7230KV (Radiator Pressure Tester & Vacuum-Type Cooling System Kit)

Radiator Cap Application:

NO 0: Thermometer
NO 1: Pressure Testing Pump with Gauge
NO 2A: Connector R123/R124 (Black Color)
NO 2B: Connector R123/R125 (Blue Color)
NO 3: Mercedes Benz (w123, w126, w124, w201) GM (Buick) Jeep
NO 5: Honda, Toyota, Suzuki, Mitsubishi, Chrysler, Acura, Lexus
NO 6: Mercedes Benz (ML-class, W163, W164) GM (achiva, skylark, gramd am-1992-2002)
NO 7: Volve, Saab, Sterling, Citroen, Renault, Fiat, Alfa, Jeep, Mini
NO 8: VW (Vento, T4, Passa-1996, Golf, Beetle, Sharan)
NO 9: Audi (A4, A5, A6), BMW 345, VW (Passa-1997-2002), Porsche (Cayenne)
NO 10: BMW (E46, E36, E34, E39, E38, E32, E90)
NO 11: Audi, VW
NO 12: Ford Mondeo, International, Land Rover, Opel, Ssangyang Motor
NO 13: Mercedes Benz (C-class, E-class, S-class, W140, W220, W124, W210, W211, W215, W216, W221, R230)
NO 14: Ford Mondeo, Focus, C-MAX03
NO 15: Mazda (M3)
NO 16: Mercedes A-class (W168)
NO 17: BMW E60, E63, E64, E65
NO 18: VW Sharan 1.8T2.8
NO 19: Toyota Rav4, Previa

KA-7561K (MASTER IMPORT COMPRESSOR CLUTCH, SEAL & BEARING)

This specialised tool includes all the tools necessary to replace seals, clutches and clutch bearing on Diesel Kiki (Zexel), Hitachi, Mitsubishi, Nippondenso, Seiko-Seiki and Sanden 505, 507, 508, 510, 575, 708 and 709. Set is packaged into a heavy blow case. Set includes instruction manual.

Contains:

1. KA-0101 UNIVERSAL FEELER GAUGE SET
2. KA-5010 UNIVERSAL CLUTCH HOLDING TOOL
3. KA-0102 PULLEY ARBOR
4. KA-0103 COMPRESSOR HOLDING FIXTURE
5. KA-0104 CLUTCH PULLER THRUST PIN
6. KA-0105 MITSUBISHI SEAL REMOVER LOCK SLEEVE
7. KA-0106 MITSHBISHI/SANDEN CLUTCH PLATE REMOVER
8. KA-0107 CLUTCH BEARING INSTALLER
9. KA-0108 NUT REMOVER & INSTALLER
10. KA-0109 PULLEY PULLER PILOT
11. KA-0110 BEARING & PULLEY INSTALLER
12. KA-0111 SANDEN 505 BEARING & PULLEY INSTALLER
13. KA-0112 SANDEN 505 BEARING & PULLEY INSTALLER
14. KA-0113 PULLEY BEARING DRIVE
15. KA-0114 PULLEY BEARING REMOVER & INSTALLER
16. KA-0115 SEAL SEAT INSTALLER
17. KA-0116 SEAL SEAT REMOVER
18. KA-0117 NIPPONDENSO CLUTCH PLATE REMOVER
19. KA-0118 CLUTCH PLATE REMOVER
20. KA-0119 SANDEN PLATE INSTALLER
21. KA-0120 SEAL PROTECTOR SLEEVE
22. KA-0121 SANDEN 505 SEAL PROTECTOR SLEEVE
23. KA-0122 MITSUBISHI SEAL REMOVER & INSTALLER
24. KA-0123 YORK SEAL REMOVER & INSTALLER
25. KA-0124 SEAL REMOVER & INSTALLER
26. KA-0125 SEAL REMOVER & INSTALLER
27. KA-0126 SEAL SEAT REMOVER & INSTALLER
28. KA-0127 SANDEN 505 SEAL SEAT REMOVER
29. KA-0128 DIESEL KIKI RETAINER RING INSTALLER
30. KA-0129 CLUTCH PLATE INSTALLER
31. KA-0130 HITACHI SPANNER PLUG REMOVER & INSTALLER
32. KA-0131 MITSUBISHI SEAL SEAT REMOVER
33. KA-0132 PULLER BODY
34. KA-0133 PULLEY REMOVER JAWS

KA-7787 (Hook and Pick Set)

• Non-slip grip handle made of steel.
• Pick and Hooks made of hardened steel.
• Storage compartment in the handle.

Content:
(1) Straight Tip Pick
(2) 90º Tip Pick
(3) Hook Tip
(4) Combinating tip
(5) Magnetic Telescoping Pick Up Tool
(6) Storage Compartment

KA-7812 (DOUBLE OFFSET RATCHET WRENCH)

8mm x 12PT x 12mm x 12PT x 300mm long

• For installation and removal of glow plugs of diesel engines of RENAULT, VW, AUDI.
• For glow plugs between the motor unit and the diesel injection pump.
• Heads with hexagon profile.
• S 8mm for operation of conductor rail screws with limit stop to guide the 8mm nut.
• S 12mm for the operation of glow plug.

KA-7812A (DOUBLE OFFSET RATCHET WRENCH)

• For installation and removal of glow plugs of diesel engines of RENAULT, VW, AUDI.
• For glow plugs between the motor unit and the diesel injection pump.
• Heads with hexagon profile.

8mm x 12PT x 10mm x 12PT x 300mm long.

• S 8mm for operation of conductor rail screws with limit stop to guide the 8mm nut.
• S 10mm for the operation of glow plug.

KA-8214 (Diesel Fuel Pump Timing Set)

This specialised tool is designed for resetting the timing position on Diesel Engines.

Application for following fuel pumps: Bosch Ep/VeRotory, Kikki, Nippon Denso, Cav Roto diesel in Alfa Romeo, Audi, BMW, Daihatsu, Fiat, Ford, Isuzu, Iveco, Lancia, Land Rover, Mazda, Mitsubishi, Nissan, Renault, Rover And Volkswagen.

KT-0307K (7PCS FLEXIBLE SOCKET WRENCH)

7PCS/PH
Size: 8, 10, 12, 13, 14, 17, 19mm

KT-372BGLS-1 (DRIVE ROTOR STUBBY RATCHET)

3/8" & 1/4" BIT

KT-472GR (Flex Head Ratchets Type: 1/2", L: 430MM/16-1/2")

D: 49mm
T: 41mm
TEETH: 72
L: 430MM/16-1/2"
G: 860g, PCS: 30
GW: 26/1.3 kgs

SB-2526 (Huei Injection Test Kit - Ford, Jackaroo, etc.)

Huei Injection Test Kit for Ford, Jackaroo, etc.